How to Install a PVC Fence
There are some things to keep in mind when you're considering installing fencing. First, decide where you want the fence to be erected. Next, you need to prepare the ground. Then, you'll have to place the posts. You might also need to adjust the height based on the dimensions and shape of your property.
Preparing the ground
Preparing the ground for the fence is an essential step in the process. This is because the fence posts have to be buried in a secure way. If they aren't secured, the fence could easily blow over in the wind.
Before digging, check with your local utility provider to confirm that there aren't any underground utilities that could impede the construction. You can call 811 to make sure that your yard is marked for underground lines.
A gravel base must be prepared for the fence posts. This will let water drain from the posts. It also provides a solid foundation for the blocks that will be erected.
Once you have the base you can begin to install the vinyl fence. The material must be at least four feet long and one inch thick. You can use an auger to dig the holes for fence posts in the event that you have it.
Before digging, you must remove any plants or trees that could interfere with the excavation. Sometimes, it is easier to remove the soil than dig it. Avoid digging in sandy or rocky soil if you have to.
Next, you will need to mark the high and low points of your yard. This can be accomplished by using the string level. Attach the string level to stakes approximately 1 foot above the ground. The string level will serve as a reference for the fence posts.
You will need to drill pilot holes in case your land is very dry. This will help the process go much faster.
You will also need to mark your holes. This can be done with spray paint or a marker. You can also use a mason's line to ensure that the posts are straight.
You can also fill the gap with decorative stones. They are great for small gaps. However when you have a larger gap, you will require a different strategy. It is also possible to put dirt inside the gap. This is a cost-effective and affordable solution.
Placement of the posts
It can be difficult to locate the posts. The first step is to find the ideal spot. This can be done with an apex level, a line mark made to accommodate the post width, or a measuring wheel.
Next, set the corner and end posts in place. Also, set the middle and top rails. Cutting is sometimes required. Rails can be used to create an alternative to posts as a spacer.
After you have located the center of each hole You can use a tape measure or stakes to mark the center of the post. To determine the depth, you can also use stringline. Once you've drawn your string line then tie the ends of the string. This will ensure the fence will be straight.
Once the posts are securely set and the posts are in place, fill the bottoms with six inches of dirt. This will help keep the posts in place, and also provide drainage for the base.
Make use of a quick-setting concrete for setting fence posts in concrete. This is a kind of concrete that sets within three to four minutes. You should not tighten the panels when installing privacy fencing. The panels should be positioned 22 inches above ground. The panels should be secured using #10 x 1" self-tapping stainless steel screws.
The posts can be attached to your fence using two screws. If you are building a privacy fence you should leave one screw at the top rail. Duct tape can be used to cover the bottom rails before inserting them into the posts. This will stop concrete website from getting into the horizontal rails below.
After you are satisfied with the design, you can take off the duct tape. Then, you can insert the top rail into each of the posts. The pickets may be attached to the rails.
You can also install lower rails at the corners. Aluminum u-channel is a great way to attach the rails to your posts.
Assembling the panels
The alignment of the fence posts up correctly is crucial to the successful installation of a vinyl fence. Based on the design of your fence, you may need to use different techniques. These steps can help you begin regardless of whether you're looking to build an oval or square fence.
Before you begin, be sure to read your deed and local Zoning laws. Inform neighbors about your plans. If you plan to install fencing made of vinyl you may have to apply for an approval for building.
Once you have all your posts set, it's time to install your rail brackets. These are screws that are fixed to the outside of the post. This makes it easier to manipulate the posts once they are installed.
Before installing your rail brackets, be sure that you have installed the rail that is on the bottom. Vinyl panels that are pre-assembled usually come with two rails. You may need to cut the rails to fit your terrain.
After your bottom rail is in place You can then install the middle rail. You can also install the top rail the same way. This step can be done by using an aluminum uchannel. It can be inserted into the posts using #8 x 1'’ screws.
You can then attach your pickets one by one. Once they're all set then you can begin attaching your C channel brackets. To ensure they stay in place you can set stakes at their corners. To join stakes using cotton string.
You can also use a spray paint marker to mark your line. This will ensure that the fence is straight when it is set.
Finally, you should install your privacy panels. They should be placed on the backside your fence. You can also add pea gravel to your holes to keep them in place. You can make your slope less steep by putting your fence panels on one side so that they "step down". If the slope is steep the fence will have to be constructed in a manner that it "steps down".
Problems with height changes
If you're planning to put a PVC fence, you may have trouble when it comes to lining up the posts. There are two methods to go about it. One is to lay the posts on the ground and the other is to lay them out. The first method is simpler and ensures that concrete is laid around each post. The second method requires you to dig out the posts and then backfill with dirt.
Make sure you have enough backfill to keep the posts in place when digging them out. It is necessary to dig around six inches in order to place the posts into the base of the gravel. To drill holes, you can also use a hole driller. The tension bar can be welded to the mesh in the final step. Then you should staple the upper part of the mesh to the fence.
If you're having difficulty aligning the posts, you can eliminate any rails that are too high. This is a challenging process but you should be able do it if you have two persons helping you. You can make the bolt threads tighter using the help of a hammer or chisel. This will stop the bolts from slipping out when you remove the fence's top.